Pulp & Paper
Machine condition monitoring based on oil analysis has become an important, if not mandatory, maintenance practice for pulp and paper companies. An effective oil analysis program w...
نظرة عامة على الصناعة
Machine condition monitoring based on oil analysis has become an important, if not mandatory, maintenance practice for pulp and paper companies. An effective oil analysis program will keep important manufacturing assets such as pumps, gears, bearings, compressors, engines, hydraulic systems and other oil-wetted machinery in operation by reducing unexpected failures and costly unscheduled downtime.
الميزات الرئيسية
Machine condition monitoring based on oil analysis has become an important, if not mandatory, maintenance practice for pulp and paper companies. An effective oil analysis program will keep important manufacturing assets such as pumps, gears, bearings, compressors, engines, hydraulic systems and other oil-wetted machinery in operation by reducing unexpected failures and costly unscheduled downtime.
For pulp and paper companies the drying roll is at the heart of production and downtime can cost many thousands of dollars an hour for larger facilities. Consequently the oil-wetted machinery, in a paper rolling machine, consisting primarily of gears and bearings is of critical importance.
Challenges
The heavy loads, high speeds and dirty, wet conditions make pulp and paper production a tough environment for any machine. Lubrication oil provides a thin layer of protection between moving metal parts. This layer is often on a few microns thick, so maintaining oil cleanliness is paramount. Water, dirt, sawdust and metal particles can interfere with that microlayer of lubrication oil and damage or destroy your valuable equipment.
Consistent and frequent oil analysis is the best defense against failures and costly downtime. Not only can oil analysis prevent failures, it can also let you know that it's safe to extend the lifetime of your oil, saving considerable money on new oil, labor, filters and disposal of lubrication oil.
For pulp and paper companies the drying roll is at the heart of production and downtime can cost many thousands of dollars an hour for larger facilities. Consequently the oil-wetted machinery, in a paper rolling machine, consisting primarily of gears and bearings is of critical importance.
Challenges
The heavy loads, high speeds and dirty, wet conditions make pulp and paper production a tough environment for any machine. Lubrication oil provides a thin layer of protection between moving metal parts. This layer is often on a few microns thick, so maintaining oil cleanliness is paramount. Water, dirt, sawdust and metal particles can interfere with that microlayer of lubrication oil and damage or destroy your valuable equipment.
Consistent and frequent oil analysis is the best defense against failures and costly downtime. Not only can oil analysis prevent failures, it can also let you know that it's safe to extend the lifetime of your oil, saving considerable money on new oil, labor, filters and disposal of lubrication oil.
الاختبارات والتطبيقات النموذجية
Wear
Particle count - a high particle count or a rapid increase in particles can foreshadow an imminent failure.
Particle composition - it is often important to understand the elemental composition of particles in order to find out where they came from. Optical Emission Spectroscopy gives the user elemental information for up to 32 elements, from Li to Ce (varies with application).
Particle type - The size, shape and opacity of particles is used to determine if they are from cutting wear, sliding wear, fatigue wear, nonmetallic or fibers. This allows operators to determine the type of wear debris, wear mode and potential source from internal machinery components.
Ferrous wear - Ferrous wear measurement is a critical requirement for monitoring machine condition. The high sensitivity magnetometer measures and reports ferrous content in ppm/ml, and provides ferrous particle count and size distribution for large ferrous particles.
Chemistry
Total Acid Number (TAN) - TAN is measured to determine the corrosive potential of lubrication oils. If the TAN gets too high the oil can induce corrosion of machine parts and should be changed.
Viscosity - The main function of lubrication oil is to create and maintain a lubrication film between two moving metal surfaces. Insuring the viscosity is within recommended ranges is one of the most important tests one can run on lube oil.
Contamination
Water- Water contamination in industrial oils can cause severe issues with machinery components. The presence of water can alter the viscosity of a lubricant as well as cause chemical changes resulting in additive depletion and the formation of acids, sludge, and varnish.
Particle count - a high particle count or a rapid increase in particles can foreshadow an imminent failure.
Particle composition - it is often important to understand the elemental composition of particles in order to find out where they came from. Optical Emission Spectroscopy gives the user elemental information for up to 32 elements, from Li to Ce (varies with application).
Particle type - The size, shape and opacity of particles is used to determine if they are from cutting wear, sliding wear, fatigue wear, nonmetallic or fibers. This allows operators to determine the type of wear debris, wear mode and potential source from internal machinery components.
Ferrous wear - Ferrous wear measurement is a critical requirement for monitoring machine condition. The high sensitivity magnetometer measures and reports ferrous content in ppm/ml, and provides ferrous particle count and size distribution for large ferrous particles.
Chemistry
Total Acid Number (TAN) - TAN is measured to determine the corrosive potential of lubrication oils. If the TAN gets too high the oil can induce corrosion of machine parts and should be changed.
Viscosity - The main function of lubrication oil is to create and maintain a lubrication film between two moving metal surfaces. Insuring the viscosity is within recommended ranges is one of the most important tests one can run on lube oil.
Contamination
Water- Water contamination in industrial oils can cause severe issues with machinery components. The presence of water can alter the viscosity of a lubricant as well as cause chemical changes resulting in additive depletion and the formation of acids, sludge, and varnish.
موارد الصناعة
لا تتوفر موارد
نقوم حالياً بتحديث مكتبة الموارد لهذه الصناعة. عد قريباً أو اتصل بنا لطلب وثائق محددة.
طلب الوثائقالمنتجات الداعمة
Oil Analysis
ميني فيسك 3000
رقم القطعة: Q3000
MiniVisc 3000 هو مقياس لزوجة حركية محمول ثوري يوفر قياسات لزو...
Oil Analysis
باي رابتور المحمول
رقم القطعة: Raptor
محلل حجم وشكل الجسيمات المحمول Raptor هو أول نظام محمول حق...
Oil Analysis
اللزوجة الحركية المحمولة VS800
رقم القطعة: VS800
مقياس اللزوجة الحركية المحمول VS800 هو أداة دقيقة متعددة ...
Oil Analysis
جهاز أخذ عينات الضغط الموجب والسالب PC‑VES
رقم القطعة: PC‑VES
جهاز أخذ عينات الزيت المحمول PC‑VES مصمم للسوائل عالية ا...
Oil Analysis
عداد جسيمات الزيت المكتبي SLPC100
رقم القطعة: SLPC100
جهاز SLPC100 هو عداد جسيمات زيت مكتبي يستخدم طريقة العد ال...
مستعد للعثور على الحل المناسب؟
يمكن لفريقنا مساعدتك في اختيار المنتجات المثالية لتطبيقات Pulp & Paper التطبيقات